# A 15 degree cut on the end of a rectangle?

**URL:** <https://discourse.shapr3d.com/t/a-15-degree-cut-on-the-end-of-a-rectangle/8188>\
**Category:** Modeling Questions\
**Created:** [July 1, 2020, 11:22pm UTC](https://discourse.shapr3d.com/t/a-15-degree-cut-on-the-end-of-a-rectangle/8188 "2020-07-01T23:22:49Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![timurray2000](https://sea2.discourse-cdn.com/flex002/user_avatar/discourse.shapr3d.com/timurray2000/32/6704_2.png) [@timurray2000](https://discourse.shapr3d.com/u/timurray2000)\
**Post date:** [July 1, 2020, 11:22pm UTC](https://discourse.shapr3d.com/t/a-15-degree-cut-on-the-end-of-a-rectangle/8188/1 "2020-07-01T23:22:49Z")

</div>

I’m new and trying to figure this out but…

I create a rectangle, make it 1-1/2" thick (a 2x4 piece of wood).

I need to put a 15 degree angle on both ends. It’s essentially a chair leg than is at an angle.

I know this must be simple but not sure how to do this.

---

<div class="post-metadata">

**Author:** ![TigerMike](https://sea2.discourse-cdn.com/flex002/user_avatar/discourse.shapr3d.com/tigermike/32/32650_2.png) [@TigerMike](https://discourse.shapr3d.com/u/TigerMike)\
**Post date:** [July 2, 2020, 12:08am UTC](https://discourse.shapr3d.com/t/a-15-degree-cut-on-the-end-of-a-rectangle/8188/2 "2020-07-02T00:08:29Z")

</div>

Greetings,  
Here are 2 ways to achieve a 15° cut.  
-Mike

15DegCut

[https://us1.discourse-cdn.com/flex002/uploads/shapr3d/original/2X/a/a88f67fc7d91daa013ae1f7672ce0c7308e75316.MOV](https://us1.discourse-cdn.com/flex002/uploads/shapr3d/original/2X/a/a88f67fc7d91daa013ae1f7672ce0c7308e75316.MOV)

---

<div class="post-metadata">

**Author:** ![timurray2000](https://sea2.discourse-cdn.com/flex002/user_avatar/discourse.shapr3d.com/timurray2000/32/6704_2.png) [@timurray2000](https://discourse.shapr3d.com/u/timurray2000)\
**Post date:** [July 2, 2020, 2:08am UTC](https://discourse.shapr3d.com/t/a-15-degree-cut-on-the-end-of-a-rectangle/8188/3 "2020-07-02T02:08:52Z")

</div>

Well, I figured it was easy.

Thanks Mike!

---

<div class="post-metadata">

**Author:** ![TigerMike](https://sea2.discourse-cdn.com/flex002/user_avatar/discourse.shapr3d.com/tigermike/32/32650_2.png) [@TigerMike](https://discourse.shapr3d.com/u/TigerMike)\
**Post date:** [July 2, 2020, 2:19am UTC](https://discourse.shapr3d.com/t/a-15-degree-cut-on-the-end-of-a-rectangle/8188/4 "2020-07-02T02:19:05Z")

</div>

Most welcome.  
We all started where you are now. Glad to help.  
-Mike