# A fine thin curve on the outer edges only

**URL:** <https://discourse.shapr3d.com/t/a-fine-thin-curve-on-the-outer-edges-only/24989>\
**Category:** Modeling Questions\
**Created:** [March 26, 2023, 8:02pm UTC](https://discourse.shapr3d.com/t/a-fine-thin-curve-on-the-outer-edges-only/24989 "2023-03-26T20:02:12Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![Christin83](https://avatars.discourse-cdn.com/v4/letter/c/8491ac/32.png) [@Christin83](https://discourse.shapr3d.com/u/Christin83)\
**Post date:** [March 26, 2023, 8:02pm UTC](https://discourse.shapr3d.com/t/a-fine-thin-curve-on-the-outer-edges-only/24989/1 "2023-03-26T20:02:12Z")

</div>

Dear community,

On the edges of a table I want them to go up just a little bit but curvy and smooth. In the middle of the table it should be flat then going further out it should make a slight curve up. But it should be evenly going up on all edges.  
Hope this was understandable…

Attached some pictures to describe it

Thank you so much in advance!

 ![image](https://us1.discourse-cdn.com/flex002/uploads/shapr3d/original/3X/9/d/9d97b93537d7659764118cb8fadfa8627b932589.jpeg)  
 ![image](https://us1.discourse-cdn.com/flex002/uploads/shapr3d/original/3X/8/0/80a478beeae56c326413ab3465752b081b25ac0c.jpeg)

---

<div class="post-metadata">

**Author:** ![Oregonerd](https://sea2.discourse-cdn.com/flex002/user_avatar/discourse.shapr3d.com/oregonerd/32/8012_2.png) [@Oregonerd](https://discourse.shapr3d.com/u/Oregonerd)\
**Post date:** [March 27, 2023, 4:57pm UTC](https://discourse.shapr3d.com/t/a-fine-thin-curve-on-the-outer-edges-only/24989/2 "2023-03-27T16:57:26Z")

</div>

SWEEEEEEEP. 😁

 ![sweep1](https://us1.discourse-cdn.com/flex002/uploads/shapr3d/original/3X/f/8/f83186a81556516ba9a7342e95c492b0e55eee25.jpeg)  
 ![sweep2](https://us1.discourse-cdn.com/flex002/uploads/shapr3d/original/3X/8/0/80d9509dcd880dd9fc4dd1d4fc74f6825b80e596.jpeg)  
 ![sweep3](https://us1.discourse-cdn.com/flex002/uploads/shapr3d/original/3X/6/7/674bfd3d5829ae71c4d1fee9724494bf858db54c.jpeg)

---

<div class="post-metadata">

**Author:** ![Oregonerd](https://sea2.discourse-cdn.com/flex002/user_avatar/discourse.shapr3d.com/oregonerd/32/8012_2.png) [@Oregonerd](https://discourse.shapr3d.com/u/Oregonerd)\
**Post date:** [March 27, 2023, 5:02pm UTC](https://discourse.shapr3d.com/t/a-fine-thin-curve-on-the-outer-edges-only/24989/3 "2023-03-27T17:02:53Z")

</div>

Nice table!  
I made a plain to draw on (perpendicular to a point on a line). Rotated it 90. Drew on it and then swept it along the table edge.

---

<div class="post-metadata">

**Author:** ![Christin83](https://avatars.discourse-cdn.com/v4/letter/c/8491ac/32.png) [@Christin83](https://discourse.shapr3d.com/u/Christin83)\
**Post date:** [March 27, 2023, 6:40pm UTC](https://discourse.shapr3d.com/t/a-fine-thin-curve-on-the-outer-edges-only/24989/4 "2023-03-27T18:40:13Z")

</div>

So nice! Thank you it worked perfectly