# Anyone ever lose the midpoint in sketch?

**URL:** https://discourse.shapr3d.com/t/anyone-ever-lose-the-midpoint-in-sketch/41428
**Category:** Technical issues and bugs
**Created:** [August 8, 2026, 2:49pm UTC](https://discourse.shapr3d.com/t/anyone-ever-lose-the-midpoint-in-sketch/41428 "2026-08-08T14:49:40Z")
**Posts on this page:** 5
**Page:** 1

<div class="post-metadata">

### Author: ![anon14694028](https://avatars.discourse-cdn.com/v4/letter/a/b9bd4f/32.png) [@anon14694028](https://discourse.shapr3d.com/u/anon14694028)
#### Post date: [August 8, 2026, 2:49pm UTC](https://discourse.shapr3d.com/t/anyone-ever-lose-the-midpoint-in-sketch/41428/1 "2026-08-08T14:49:40Z")

</div>

Assuming this started after an update, but on a PC, I haven’t been able to re-enable it.  
Thanks -

 ![image](https://us1.discourse-cdn.com/flex002/uploads/shapr3d/original/3X/4/8/484f6f50f58579a51cdf8c52ebb569547ca7ffa9.png)

---

<div class="post-metadata">

### Author: ![Xdrakosha](https://sea2.discourse-cdn.com/flex002/user_avatar/discourse.shapr3d.com/xdrakosha/32/24881_2.png) [@Xdrakosha](https://discourse.shapr3d.com/u/Xdrakosha)
#### Post date: [August 8, 2026, 2:55pm UTC](https://discourse.shapr3d.com/t/anyone-ever-lose-the-midpoint-in-sketch/41428/2 "2026-08-08T14:55:46Z")

</div>

It can happen from time to time. If you can reproduce the issue I would recommend to submit a ticket to the support. Meanwhile you can try to apply midpoint constraint manually.

---

<div class="post-metadata">

### Author: ![margriet](https://sea2.discourse-cdn.com/flex002/user_avatar/discourse.shapr3d.com/margriet/32/36415_2.png) [@margriet](https://discourse.shapr3d.com/u/margriet)
#### Post date: [August 8, 2026, 3:02pm UTC](https://discourse.shapr3d.com/t/anyone-ever-lose-the-midpoint-in-sketch/41428/3 "2026-08-08T15:02:18Z")

</div>

Yes, i have had the same on the iPad! I saved my design, closed Shapr3d, then open it again and it is back. It is since a short while. But I have to admit, I use Shapr3d just a short while in total.

---

<div class="post-metadata">

### Author: ![DrKronos](https://sea2.discourse-cdn.com/flex002/user_avatar/discourse.shapr3d.com/drkronos/32/36064_2.png) [@DrKronos](https://discourse.shapr3d.com/u/DrKronos)
#### Post date: [August 9, 2026, 3:04pm UTC](https://discourse.shapr3d.com/t/anyone-ever-lose-the-midpoint-in-sketch/41428/4 "2026-08-09T15:04:45Z")

</div>

I had it happen, yes.

There is a little “trick” to find the midpoint even if it doesn’t show as a dot for some reason:

If you slide your mouse cursor along the line, the little tool tip changes from “edge” to “intersection” when you’re over the midpoint.

Not ideal, but a kind of workaround when this bug occurs.

---

<div class="post-metadata">

### Author: ![ZsofiGy](https://avatars.discourse-cdn.com/v4/letter/z/90ced4/32.png) [@ZsofiGy](https://discourse.shapr3d.com/u/ZsofiGy)
#### Post date: [August 10, 2026, 12:47pm UTC](https://discourse.shapr3d.com/t/anyone-ever-lose-the-midpoint-in-sketch/41428/5 "2026-08-10T12:47:35Z")

</div>

Hi, if you can reproduce the issue, please send us the steps via support ticket at [this link](https://support.shapr3d.com/hc/en-us/requests/new). Thank you!