# First project
**URL:** https://discourse.shapr3d.com/t/first-project/33833
**Category:** Share your creations
**Created:** [September 21, 2024, 3:36pm UTC](https://discourse.shapr3d.com/t/first-project/33833 "2024-09-21T15:36:32Z")
**Posts on this page:** 8
**Page:** 1
### Author:  [@Aner](https://discourse.shapr3d.com/u/Aner)
#### Post date: [September 21, 2024, 3:36pm UTC](https://discourse.shapr3d.com/t/first-project/33833/1 "2024-09-21T15:36:32Z")
Hi everyone!
I wanted to show off my first model, which is a knife. I’m just starting my adventure with CAD, so I’m mega excited that I managed to finish it. The workmanship isn’t perfect, but I’m happy with the result for a first time. I would welcome any suggestions and feedback! 🙂
If I can figure out how, I’ll make it in future
I attach the picture
and look forward to your comments!
---
### Author:  [@jean-philippe2](https://discourse.shapr3d.com/u/jean-philippe2)
#### Post date: [September 21, 2024, 4:36pm UTC](https://discourse.shapr3d.com/t/first-project/33833/2 "2024-09-21T16:36:33Z")
Hi,
It’s not bad for a first time, bravo!
I find the handle a little too thin, not thick enough.
The pattern on the handle is a bit rough.
You will also have to work on the spikes (fillets, bevels…)
---
### Author:  [@Aner](https://discourse.shapr3d.com/u/Aner)
#### Post date: [September 22, 2024, 8:24pm UTC](https://discourse.shapr3d.com/t/first-project/33833/3 "2024-09-22T20:24:27Z")
Thank you, Jean, for the advice!
I made the handle thicker and also worked on the pattern as you suggested.
I was having trouble with the fillets, but after redoing the sketch, everything is working well now.
---
### Author:  [@jean-philippe2](https://discourse.shapr3d.com/u/jean-philippe2)
#### Post date: [September 22, 2024, 8:30pm UTC](https://discourse.shapr3d.com/t/first-project/33833/4 "2024-09-22T20:30:27Z")
I think this is much better. Well done !
---
### Author:  [@charly44300](https://discourse.shapr3d.com/u/charly44300)
#### Post date: [September 23, 2024, 1:50pm UTC](https://discourse.shapr3d.com/t/first-project/33833/5 "2024-09-23T13:50:05Z")
Pourriez-vous donner une adresse de publication nous pourrions ainsi voir votre couteau sous des angles et zoom différents. Merci
---
### Author:  [@Aner](https://discourse.shapr3d.com/u/Aner)
#### Post date: [September 23, 2024, 3:11pm UTC](https://discourse.shapr3d.com/t/first-project/33833/6 "2024-09-23T15:11:32Z")
Sure, no problem.
> **[Shapr3D Webviewer](https://collaborate.shapr3d.com/v/qA0tjmY0kl0sSUrwS9l5O)**
>
> Share your designs with a single click.
---
### Author:  [@jean-philippe2](https://discourse.shapr3d.com/u/jean-philippe2)
#### Post date: [September 23, 2024, 4:57pm UTC](https://discourse.shapr3d.com/t/first-project/33833/7 "2024-09-23T16:57:01Z")
yes, it’s cool 🙂
---
### Author:  [@charly44300](https://discourse.shapr3d.com/u/charly44300)
#### Post date: [September 23, 2024, 8:50pm UTC](https://discourse.shapr3d.com/t/first-project/33833/8 "2024-09-23T20:50:56Z")
Les épaisseurs sont très bien proportionnées. Encore toutes mes félicitations. Charly44300